ADJ WiFly Bar RGBA Manuel d'utilisateur Page 8
- Page / 18
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
ADJ Products, LLC - www.adj.com - WiFly Bar RGBA User Manual Page 15 ADJ Products, LLC - www.adj.com - WiFly Bar RGBA User Manual Page 16
Master-Slave Configuration:
This function will allows you to link units together to run in a Master-Slave
mode. In Master-Slave operation one unit will act as the controlling unit
and the others will react to the controlling units built-in programs. Any
unit can act as a Master or as a Slave however, only one unit can be pro-
grammed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the unit.
Use standard XLR data cables to link your units together. Remember
that the Male XLR connector is the input and the Female XLR con-
nector is the ouput. The first unit in the chain (master) will use the
female XLR connector only. The last unit in the chain will use the
male XLR connector only.
2. Set the “Master” unit to your desired mode of operation.
3. On the “Slave” units press the MODE button until “SLAu” is dis-
played. The unit is now set as the “Slave” unit. Each slave unit
must be set to the same setting.
4. Connect the rst “Slave” unit to the “Master”, and the “Slave” unit
should now start follow the “Master”.
This feature will let you link units to run in a master-slave mode with-
out the use of XLR cables.
NOTE: The ADJ RFC control must be set to OFF to use this func-
tion.
1. Follow the instructions on page 14 to set the Wireless address.
The addresses on each fixture must be the same.
2. After you have set the WiFly address, select your master unit and
set your desired operating mode.
3. Put the attenna to a upright position then turn the WiFly On, using
the WiFly power switch.
4. For the Slave units, put the unit in Slave mode. See page 15
Master-Slave configuration when setting the unit as a Slave. Then
switch ON the WiFly power switch.
4. If everything is set up correctly, the Master units WiFly status LED
will glow orange, and the slave units Wireless status LED will glow
green.
NOTE: If they do not sync up master-slave, switch the Master fix-
tures WiFly power switch off then on again.
WiFly Bar RGBA Master-Slave Configuration
WiFly Bar RGBA WiFly Master-Slave Set Up
WiFly Bar RGBA WiFly Set Up
With this feature you are able to control the unit with DMX without the
need of XLR cables. Your DMX controller must be connected to a ADJ
WiFly TransCeiver to use this function. You are able to communicate
up to 400 feet (open line of sight)
NOTE: The ADJ RFC control must be set to OFF to use this func-
tion.
1. Turn on the WiFly function using the WiFly On/Off switch and
set the attenna to a upright position.
2. Follow the instructions on page 14 to set the Wireless address.
The address must match the address set on the WiFly Transceiver.
3. After you have set the WiFly address, follow the DMX instructions
on pages 12-13 to select your desired DMX Channel mode and
set your DMX address.
4. Apply power to the ADJ WiFly Transceiver. The fixture must be set
up first before you apply power to WiFly Transceiver.
5. If everything is set up properly and the fixture is receiving a
Wireless signal, Wireless status LED next to LED screen will glow
green. Note: If the sync does not work, switch the WiFly power off
then on again.
Produits connexes et manuels pour Lumières des projecteurs ADJ WiFly Bar RGBA
(17 pages)
(16 pages)
(20 pages)
(20 pages)
(32 pages)
(16 pages)
(16 pages)GPX R308B podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Zegar GPX R308B.
Dostarczamy 1 pdf podręczników GPX R308B do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Commentaires sur ces manuels